Gym or fitness studio · 5 min read

Which gym equipment checks should happen every day, week and month?

The short answer

Every day, walk the floor for loose bolts, frayed cables, torn upholstery and odd noises, and tag any faulty machine out of use. Every week, check treadmill belt tracking and tension, cables, pulleys, selector pins, safety clips, bench and rack hardware. Every month, check bolt tightness, cable tension, guide rods and flooring edges, and have a technician service the heavy-use cardio at least once or twice a year. Write each check in a log.

Not sure about your case? Ask an expert, free ↓

Why do gym equipment checks matter?

A trainer notices a cable on the lat pulldown that looks fuzzy at the end. It has looked like that for a week. On Thursday the cable parts, the bar flies up and the weight stack drops. A daily walk-through exists for that moment.

Most gym injuries from equipment come from small, visible faults left in use: a frayed cable, a bent pin, a loose bolt, a torn pad. An insurer's risk guide on fitness equipment says frayed cables, misaligned pulleys and loose crimps should be documented and the equipment closed until repaired or replaced. A log is also your record if there is a claim, so tell your insurer how you keep it.

What should be checked, and when?

Combined from maintenance guidance by equipment makers, a gym maintenance provider, an insurer and a strength and conditioning association. The maker's manual for each machine overrides these intervals.
How oftenWhoChecks
Every dayTrainers and cleaners, with the opening walkVisual walk-through for loose bolts, cables, upholstery tears, wobble and unusual sounds. Wipe grips, consoles and benches. Confirm each machine powers on. Clear floor gaps. Tag any fault out of use
Every weekTrainer or floor supervisorTreadmill belt tracking and deck wear; bike pedals and seat posts; cables, pulleys, selector pins and attachments; dumbbell heads and handles; rack alignment, J-hooks and safeties. Test safety devices such as treadmill safety clips
Every monthTrained staff or technicianBolt tightness to the maker's specification, cable tension, pulley smoothness, guide rods and weight-stack travel, bar sleeves and collars, upholstery, flooring edges. Lubricate only where the manual says so
QuarterlyTechnician or senior trainerDeep clean under and around equipment, review the log for repeat faults, inspect high-use moving assemblies, decide repair, replace or shut down
Once or twice a yearAuthorised service providerFull service of cardio and selectorised equipment: motors, belts, alignment, tensioning, cables and electronics

Frequencies are starting points. A 24-hour gym in a humid city needs more checks than a studio open eight hours.

What do I look for on each type of equipment?

  • Treadmills: belt centred (a few millimetres off at most), no fraying, glazing or snags; deck not grooved; belt not sticking or pulling to one side; power cord and plug intact; safety key works; ventilation openings free of dust. Lubricate only if the manual says the deck needs it, with the right lubricant.
  • Cable machines and cross-overs: cables for fraying, broken strands, kinks and flattened sections; pulleys that spin freely and hold the cable in the groove; carabiners, snap hooks and attachments (never use S-hooks where the maker forbids them); stop the station at once if a cable is damaged.
  • Selectorised machines: selector pins straight and seated, guide rods clean, weight stack travel smooth, seat and back pads secure.
  • Benches and racks: welds, wobble, J-hooks, safety arms, adjustment pins; check foam and covers.
  • Barbells, plates, dumbbells: bars straight and sleeves spinning, collars working, plates not cracked, dumbbell heads tight and rubber intact; oil and brush rust off bars monthly.
  • Bikes and ellipticals: pedals, straps, seat posts, wobble, drive noise.
  • Flooring and mirrors: lifting tile edges, tears, loose mirrors. See flooring and mirrors.

For how long each type lasts and what it costs to keep running, see equipment life and maintenance and equipment AMC and repairs.

When do I take a machine out of use?

  • A frayed or damaged cable, a bent or cracked pin, a missing safety clip or a broken weld: out of use immediately.
  • A treadmill belt that sticks, drifts or has damage, an overheating smell, or an exposed wire: out of use.
  • Any unexplained noise from a loaded machine: out of use until a technician looks.

Use a red hold tag and a log entry with the date, the machine ID, the fault and the person. Take it out of the zone if you can. Never let a trainer 'just use it for today'. Then call the supplier, and note the response time. A long wait is itself a signal about the supplier.

How do I keep the log?

  • One log per machine, or one sheet per zone, with machine ID, date, check, initials and remarks.
  • A column for pass or hold, so a repeat fault is visible.
  • A monthly review by the owner or manager of repeat faults and open holds.
  • Keep invoices, serial numbers and warranty cards in the same folder.
  • Keep the logs for at least a year, and longer for anything involving an incident.

This is practical guidance, not legal advice. For injuries and claims, read the incident and insurance pages with your insurer.

What usually goes wrong?

  • Checking cleanliness and calling it safety. A shiny machine is not a safe one.
  • Treating an old, fuzzy cable as 'fine for now'.
  • Lubricating with the wrong product, or lubricating a deck that does not need it.
  • No hold tag, so the broken machine is back on the floor by evening.
  • No technician visit in the first year because the machines are new.

If you want a log format for your floor, tell us your equipment and size and we can help you draft one.

Questions people ask

How often should a treadmill be serviced?

Maker manuals vary, but guides suggest a visual check daily, belt tracking and tension weekly, and a technician service once or twice a year in a busy gym. Follow the manual for your model.

What should make me stop using a machine?

A frayed or damaged cable, a bent or missing pin, a cracked weld, a belt that sticks or drifts, or any unexplained noise or smell. Tag it out and call a technician.

Do I need a written log?

It is not a legal rule, but it shows your insurer and your members that you check. Keep it for at least a year.

Operations · Gym or fitness studio

More on operations for a gym or fitness studio

20 pages on this. You are on number 10.

  1. How do I tell commercial gym equipment from home-use equipment that will break in a year?
  2. How do I track gym enquiries and follow-ups so no walk-in is lost?
  3. Which gym equipment checks should happen every day, week and month?
  4. How do I build training, standards and an operations manual for gym franchisees?
  5. How do I write SOPs for a gym: opening, sales, training and cleaning?
  6. My electricity bill is huge. How do I cut a gym's power cost without hurting the experience?
  7. What should I ask a gym equipment supplier before I sign: warranty, spares, installation, buy-back?
  8. How do I maintain gym equipment, and is an annual maintenance contract worth it?
All 20 on operations →

Reading about it is one thing; doing it in your gym or fitness studio is another. If you'd like a hand running it smoothly day to day, tell us where you are and a person will reply, free.

Get help with this ↓

What now?

Next question · 3 of 6 in Running it day to dayMy electricity bill is huge. How do I cut a gym's power cost without hurting the experience? →

Where are you?

One tap, and we point you to the right next step.

Menu

Read

Ask an expert Ask an expertFree, real peopleHub
Ask an expert