Hire in this order: a design-and-sales person who can read a site, a technical draftsperson who turns the design into a cut list, a lead fitter with a helper, and only then factory staff. Most errors come from the hand-offs between these roles, so give each one a signed drawing to work from.
As planning estimates, a design-sales executive in a tier-2 city earns roughly ₹18,000–35,000 a month plus incentive, a detailer ₹20,000–40,000, and an experienced fitter ₹900–1,500 a day or a piece rate per kitchen. Metro figures run 20–40% higher. These are ballparks to adjust after local enquiry. Costs and licences are in the modular kitchen playbook.
The first four hires, in order
| Role | What they own | Estimated monthly pay (tier-2 / metro) |
|---|---|---|
| Design and sales executive | Site visit, first layout, 3D, quote, follow-up and closing; the person clients trust | ₹18,000–35,000 / ₹25,000–50,000 plus 1–3% incentive |
| Technical draftsperson (detailer) | Converts the approved design into dimensioned drawings, cut lists, edge-band flags and hardware list | ₹20,000–40,000 / ₹28,000–55,000 |
| Lead fitter | Reads the drawings, installs carcasses level, hangs shutters, fixes the stone-top fit-up | ₹900–1,500 a day, or ₹6,000–15,000 a kitchen / ₹1,200–2,000 a day |
| Fitter's helper | Carries boards, drills, cleans, holds panels | ₹500–800 a day / ₹700–1,000 a day |
| Project coordinator | Site readiness calls, delivery slots, snag list, warranty tickets | ₹22,000–40,000 / ₹30,000–50,000 |
In the first year, the owner often is the designer and the measurement lead. Hire the detailer second, because a good designer-seller who also detail-drafts becomes a bottleneck after four or five open jobs. A drawing that goes to the factory without a second pair of eyes is the commonest source of remake costs.
Site measurement and handover roles
Measurement is a skill, not a chore. A measurement lead takes the first-visit sketch, the post-tiling final measurement, and the pre-installation readiness check. Three visits, three checks, signed each time by the client or their representative.
- Visit 1 (design measure): rough dimensions, appliance models, client habits (which hand cooks, who is tall) and photographs.
- Visit 2 (final measure): after civil work, plastering and tiling, with the stone-top fabricator present if possible; this one drives the cut list.
- Visit 3 (readiness check): water and drain stubs, electrical points, gas line, platform level and floor tiling complete; no panel leaves the factory until this is ticked.
Train the measurer to note beam and column offsets, ceiling slope, window opening and handle swing, skirting thickness, and distance from the platform end to the nearest door. A 15 mm skirting that was not noted becomes a 15 mm gap at the back of every base unit.
Factory roles if you go in-house
Once volume justifies a saw and edge bander, you add a small shop-floor team. Pay below is an estimate by role; operators who have worked on automatic lines are scarce in smaller towns, and many owners train a helper for three to six months instead.
| Role | Duties | Estimated monthly pay (tier-2 / metro) |
|---|---|---|
| Panel saw operator | Optimised cuts from the cut list, grain direction, labelling each part | ₹18,000–30,000 / ₹24,000–38,000 |
| Edge bander operator | Machine setup for 0.8 mm and 2 mm bands, glue temperature, trimming, buffing | ₹17,000–28,000 / ₹22,000–35,000 |
| Boring and assembly hand | 32 mm system holes, hardware pre-fit and cam checks before packing | ₹14,000–24,000 / ₹18,000–30,000 |
| CNC programmer-operator | Converts files to tool paths, nests sheets, runs and checks first-off | ₹30,000–60,000 / ₹40,000–75,000 |
| Packing and dispatch | Corner protectors, stretch wrap, labelling by room and wall | ₹12,000–18,000 / ₹15,000–22,000 |
A factory with workers triggers more compliance than a studio: labour-code registration, worker safety, employee provident fund and insurance rules where you cross thresholds. I have not verified current thresholds, so ask your CA and the state labour department.
Fitters: crews, piece rates and quality
Most kitchen businesses run installation through independent crews working on piece rates, not on a payroll. That keeps cost variable, but you lose control over quality unless you set the standard in writing.
- Piece rate per job or per running foot, with a deduction schedule for rework, so a crew that leaves a gap pays for the fix.
- A site checklist signed at handover: levelling checked, shutters aligned within a stated tolerance, drawers closing soft, silicone neat at the sink, site cleaned.
- Uniform and ID cards so a stranger in the client's home is identifiable.
- Worker injury cover: for contract labour on client premises, ask your CA and lawyer about contract-labour rules, injury compensation and whether you need group accident insurance; I have not verified the specifics.
- A written crew agreement: not a labour-law substitute, but it records rates, damage liability, tools, timelines and who pays for rework.
Pay a small bonus for jobs with no snag-list items at handover and no warranty call in the first 60 days. It is cheaper than the call-out costs and teaches crews what the standard is.
Where to find people and how to vet them
| Role | Where to look | Vetting task |
|---|---|---|
| Designer-seller | Interior design diplomas and polytechnics, kitchen dealers' former sales staff, architects' junior designers | Give a bare L-shaped plan and ask for a base-and-wall layout with work triangle and one pull-out; check clearances |
| Detailer | ITI draughtsmen, furniture workshops, factories using Polyboard-type tools | Hand a kitchen drawing and ask for a cut list with edge-band flags; check for errors on the 32 mm hole positions |
| Fitter | Other studios' fitters, carpenter lanes, referrals from hardware distributors | Pay for a half-day trial: hang one wall unit level, align two shutters and fit a soft-close channel |
| Factory operator | Local panel-processing units, machine dealers' operators, technical schools | Ask for a cut-and-edge run on scrap boards; check squareness and chipping |
| Coordinator | Real estate and appliance service teams | Hand over a messy WhatsApp thread and ask them to build a delivery plan |
Poaching is common between studios and fitters. Keep your designer's incentive tied to jobs that complete, not just those booked, so they stay interested in the site.
Employment law, contract labour, provident fund, insurance and apprentice rules vary by state and headcount. This is general information, not legal advice; confirm with a CA or lawyer.
Freelancer or salaried?
| Role | Freelance or contract | Salaried |
|---|---|---|
| Designer | Freelance 3D designers at ₹1,500–4,000 per kitchen (estimate) for peaks | Once you handle more than six or seven design cases a month |
| Detailer | Outsourced cut-list drafting by the kitchen or per-hour | When drawing errors start costing you more than a salary |
| Fitter | Piece-rate crews, usually | A core fitter on a fixed wage once you have installations most weeks |
| Factory staff | Not usually | Always salaried or on a clear contract |
| Accounts | Part-time bookkeeper or a CA firm | Never full-time at the start |
If your founders are also designers or fitters, document your standard layouts, hardware rules and check lists in a one-page handbook. That is the only way a new hire can match your quality in their first month. For job-tracking, see the software page.
Before you hire anyone
More on starting a modular kitchen business
- Start hereThe full playbook →Models, licences, startup costs and the steps to your first customer.
- Go deeperWhat to buy →Measuring kit, a working display, fitter tools and sample boards; rent machine time before buying machines.
- Go deeperGetting customers →Builder handovers, trade partners and local search; transparent running-foot quotes and your first 10 jobs.
- Go deeperFinding suppliers →Boards, shutters, hardware, edge band, stone and job-work: where to find, test and negotiate each.
Questions people ask
Who should a new modular kitchen business hire first?
A design-and-sales person who can read a site and sell a layout, followed by a technical draftsperson. Owners often play the first role themselves for a year. Add a lead fitter on a piece rate early, because installation quality decides referrals. Hire factory operators only when you buy machines.
How much do kitchen fitters earn in India?
Experienced fitters in tier-2 cities commonly earn about ₹900–1,500 a day, or a piece rate of ₹6,000–15,000 a kitchen, with metros 20–40% higher. These are estimates that vary with kitchen size and finishes. Ask local studios before fixing your rates, and pay quality bonuses for clean handovers.
Should installers be employees or contractors?
Many studios use independent crews on piece rates, with a written agreement on rates, rework liability and damage, and a quality checklist. Employment status depends on how much control you have and on state law, so ask a CA or lawyer. Keep one trusted lead fitter closer to the business.
How do I test a candidate fitter?
Pay for a half-day trial. Ask them to hang one wall unit level on a test wall, align two shutters evenly and fit a soft-close channel. Check gaps with a feeler gauge or coin, drawer closing, and how they clean up. A fitter who measures twice and speaks up about site problems is worth more than a fast one.
Do I need a detailer or can the designer do cut lists?
A designer can do cut lists for the first few jobs, but errors in the 32 mm holes, grain direction or edge-band flags cost real money. Once you have four or five jobs open, hire a detailer so every drawing is checked by someone other than the person who sold the kitchen.
