Read first
The sample was perfect. The batch was not
A founder approves a lovely sample, pays half the order, and receives cartons with a different shade of fabric, stitches that open at the seam, and labels cut a few millimetres wide. The maker's answer is that the sample was hand-finished and bulk is bulk. Neither of them had written down what "approved" meant.
Checking a factory is mostly about closing that gap: what you saw, what they promised and what shows up in the carton.
Papers to ask for before the visit
- GST registration, checked on the government search page for name and address match.
- Category licences: for example a food safety licence for food, a manufacturing licence for cosmetics, a factory licence where the law requires one. What applies depends on your product; the category rules decide, not this page.
- Udyam or other registration, to confirm what they say about their size.
- A sample test report or batch record, even a one-page internal one.
- Names of two customers you can call.
Do not be put off if a small unit's papers look simple. Be put off if there are none, or if the name on the licence differs from the name on the door and nobody can explain it.
A one-day visit checklist
Test what they will really send
Ask for three things in your sample round, and pay for them if needed. First, the approved sample. Second, a piece pulled from a small production run, not hand-made. Third, a replacement of the same item a week later, to see consistency. Compare the three side by side, in daylight, with a measuring tape or a scale.
Write the standard down on a single page: dimensions with tolerance, weight, shade reference, fabric or ingredient list, pack, label position. Both of you sign it. That page is your quality agreement; the manufacturing agreement then points to it.
Keep two sealed approved samples, one with you and one with the maker. When a batch arrives, you compare against the sealed sample, not against your memory.
When an independent inspector is worth it
A third-party inspection agency can check a batch before it leaves the factory, against your written standard. It makes sense when the factory is far away, the order is large relative to your cash, or this is your first order with this maker. It does not make sense for a first batch of a few hundred pieces from a unit down the road; a day of your own time costs less. Ask any agency for its report format and fee in writing before you book.
What usually goes wrong
- Visiting once, then never again. Quality drifts when nobody looks. Visit the second batch too.
- Accepting an oral standard. "Same as sample" is not a standard.
- Paying the whole advance before seeing a production piece.
- Believing a certificate framed on the wall is current. Ask for the number and date.
- Forgetting the packing stage. Many bad batches are good products that were packed badly.
If you cannot visit, ask for a live video walk of the floor and the product on the line, then still pay in stages.
Apply it to your maker
Write your one-page standard before you visit, so you walk in with a reference. If you are choosing between two makers and want a second opinion on what you saw, tell us where you are. For what to do once batches start arriving, read quality control on every batch.
Questions people ask
Do I need to visit the factory?
For a first order, yes if you can. If not, a live video walk of the floor plus references from two customers is the next option. Either way, pay in stages.
How much advance should I pay a manufacturer?
There is no fixed figure; terms vary by maker and product. Pay in stages tied to events you can check, such as sample approval, start of production and dispatch, and avoid paying the full amount before you have seen a production piece.
What if the bulk batch does not match the sample?
Photograph and measure the difference against your signed standard and the sealed sample, tell the maker in writing the same day, and do not use or sell the batch until the issue is settled. See the page on quality control per batch.
Operations · Product brands
More on operations for a product brands
16 pages on this. You are on number 7.
- How to find a good contract manufacturer for your brand in India
- What can your brand do with slow-moving or dead stock?
- How to check a factory's quality before you pay for your brand's first batch
- How to plan stock and cash for Diwali, wedding and sale seasons in your brand
- Which courier or shipping aggregator should your brand use in India?
- Minimum order quantity and samples: how to get a smaller first order from a maker
- What is an NDR in shipping, and what should your brand do when a delivery attempt fails?
- How to pack products so they arrive unbroken without overspending on packaging
and 8 more.
Reading about it is one thing; doing it in your product brands is another. If you'd like a hand running it smoothly day to day, tell us where you are and a person will reply, free.
Get help with this ↓What now?
Where are you?
One tap, and we point you to the right next step.